1. 服务器/VPS/主机用户Telegram电报群: https://t.me/openos
    黑群晖 Synology Telegram电报群: https://t.me/nasfan
    排除公告

i1219v网卡内网速度问题

本帖由 3139365072022-04-23 发布。版面名称:群晖 Synology DSM

  1. 313936507

    313936507 New Member

    注册:
    2022-04-05
    帖子:
    29
    我用i1219v的内网速度只有80mb/s,用2.5g网卡插的千兆路由器就有100mb/s,引导是论坛下的,直接可以装,没有改那个lm,物理机,这是咋回事
     
  2. pengtao95

    pengtao95 New Member

    注册:
    2020-06-21
    帖子:
    14
    你搜一下这个帖子:黑群晖7.1-42661。我是华擎的b360m itx主板,网卡是i1219v,很正常
     
  3. 313936507

    313936507 New Member

    注册:
    2022-04-05
    帖子:
    29
    你这个能不能实体按钮关机
     
  4. pengtao95

    pengtao95 New Member

    注册:
    2020-06-21
    帖子:
    14
    这个我还没试过
     
  5. 313936507

    313936507 New Member

    注册:
    2022-04-05
    帖子:
    29
    试试看看呗,你7.0.1引导用的哪个呀
     
  6. carney

    carney Member

    注册:
    2019-03-25
    帖子:
    44
    linux下e1000驱动可能有兼容问题,我测了下219v或lm219网卡在windows下就正常,linux下219v或lm219一般接收能跑112M,发送就是90M左右了。
     
  7. 313936507

    313936507 New Member

    注册:
    2022-04-05
    帖子:
    29
    希望有关人士能推荐个能跑满的引导。。。
     
  8. 313936507

    313936507 New Member

    注册:
    2022-04-05
    帖子:
    29
    群晖这个网卡更新只需要换个引导就可以了吗,还是要把之前的系统删掉
     
  9. 313936507

    313936507 New Member

    注册:
    2022-04-05
    帖子:
    29
    https://www.sqmn666.com/archives/esxi70-feng-zhuang-zui-xin-ban-ying-te-er-i225i219-wang-ka-qu-dong
    我的网卡是这个型号,如果用e1000e的话是不是会可能导致速度跑不满呀,我现在下载只有80mb/S,上传却没问题:110mb/s 这个网卡是不是更适合用e1000这个驱动? 0000:00:1f.6 Ethernet controller: Intel Corporation Ethernet Connection (2) I219-V
    0000:00:1f.6 Class 0200: Device 8086:15b8 DeviceName: Onboard - Ethernet Subsystem: Device 1849:15b8 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 129 Region 0: Memory at df300000 (32-bit, non-prefetchable) [size=128K] Capabilities: [c8] Power Management version 3 Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+) Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=1 PME- Capabilities: [d0] MSI: Enable+ Count=1/1 Maskable- 64bit+ Address: 00000000fee0200c Data: 4192 Capabilities: [e0] PCI Advanced Features AFCap: TP+ FLR+ AFCtrl: FLR- AFStatus: TP- Kernel driver in use: e1000e
     
  10. 313936507

    313936507 New Member

    注册:
    2022-04-05
    帖子:
    29
    lspci -Q这个命令看下你的i1219是哪个型号