1. 服务器/VPS/主机用户Telegram电报群: https://t.me/openos
    黑群晖 Synology Telegram电报群: https://t.me/nasfan
    排除公告

微星主板MPG Z390 GAMING PLUS 安装群晖不能识别硬盘

本帖由 xcgf 于 2023-08-19 发布。版面名称：群晖 Synology DSM

  1. xcgf

    xcgf Member

    注册:
    2019-11-30
    帖子:
    268
    2023-08-19 #1
    请问给位帮忙提供硬盘参数 让我能识别发现硬盘
    tc@box:~$ sudo ./rploader.sh satamap now
    Found SCSI HBAs, We need to install the SCSI modules
    Don't run this as root.
    Succesfully installed SCSI modules

    Found SCSI/HBA "00:17.0 Intel Corporation SATA Controller [RAID mode] (rev 10)" (2 drives)
    lspci: -s: Invalid slot number
    Found SCSI/HBA "" (0 drives)
    lspci: -s: Invalid slot number
    Found SCSI/HBA "" (0 drives)
    lspci: -s: Invalid bus number
    Found SCSI/HBA "" (0 drives)
    lspci: -s: Invalid slot number
    Found SCSI/HBA "" (0 drives)
    lspci: -s: Invalid slot number
    Found SCSI/HBA "" (0 drives)
    lspci: -s: Invalid slot number
    Found SCSI/HBA "" (0 drives)
    lspci: -s: Invalid slot number
    Found SCSI/HBA "" (0 drives)
    lspci: -s: Invalid slot number
    Found SCSI/HBA "" (0 drives)
    lspci: -s: Invalid slot number
    Found SCSI/HBA "" (0 drives)
    lspci: -s: Invalid slot number
    Found SCSI/HBA "" (0 drives)
    lspci: -s: Invalid slot number
    Found SCSI/HBA "" (0 drives)

    Computed settings:
    SataPortMap=1
    DiskIdxMap=00

    Should i update the user_config.json with these values ? [Yy/Nn] y
    Done.
    tc@box:~$ dmesg | grep SATA 注意大写
    [ 0.351985] ahci 0000:00:17.0: AHCI 0001.0301 32 slots 6 ports 6 Gbps 0x3f impl SATA mode
    [ 0.604996] ata1: SATA max UDMA/133 abar m2048@0x90022000 port 0x90022100 irq 120
    [ 0.604999] ata2: SATA max UDMA/133 abar m2048@0x90022000 port 0x90022180 irq 120
    [ 0.605000] ata3: SATA max UDMA/133 abar m2048@0x90022000 port 0x90022200 irq 120
    [ 0.605001] ata4: SATA max UDMA/133 abar m2048@0x90022000 port 0x90022280 irq 120
    [ 0.605003] ata5: SATA max UDMA/133 abar m2048@0x90022000 port 0x90022300 irq 120
    [ 0.605004] ata6: SATA max UDMA/133 abar m2048@0x90022000 port 0x90022380 irq 120
    [ 0.920369] ata3: SATA link down (SStatus 4 SControl 300)
    [ 0.920386] ata2: SATA link down (SStatus 4 SControl 300)
    [ 0.920402] ata1: SATA link down (SStatus 4 SControl 300)
    [ 0.920419] ata5: SATA link down (SStatus 4 SControl 300)
    [ 0.920434] ata6: SATA link down (SStatus 4 SControl 300)
    [ 0.923702] ata4: SATA link down (SStatus 4 SControl 300)
    tc@box:~$
     
  2. xcgf

    xcgf Member

    注册:
    2019-11-30
    帖子:
    268
    2023-08-21 #2
    没有人来看看 提供思路
     
  3. 翡璃月

    翡璃月 Member

    注册:
    2018-04-23
    帖子:
    45
    2023-08-22 #3
    MSI板子失敗機率很高
    能安裝成功的板子很少
    建議換ASUS或ASROCK或GIGA
     
  4. xcgf

    xcgf Member

    注册:
    2019-11-30
    帖子:
    268
    2023-08-22 #4
    我在gurd.cfg 写上
    SataPortMap=1
    DiskIdxMap=00
    硬盘查在SATA1口能识别硬盘安装。接第二块硬盘不能识别硬盘
     
  5. xcgf

    xcgf Member

    注册:
    2019-11-30
    帖子:
    268
    2023-08-22 #5
    修改成DiskIdxMap=00 SataPortMap=6 SasIdxMap=0 还是不能识别第二块硬盘
     
    最后编辑: 2023-08-23
  6. entomy1123

    entomy1123 New Member

    注册:
    2020-10-31
    帖子:
    4
    2023-08-24 #6
    我看了下这主板手册
    里面提到一句话
    "将 M.2 SATA 设备安装到 M2_1 接口时,SATA2 将无效"
    会不会是这原因?

    [​IMG]
     
  7. bdrwu

    bdrwu Active Member

    注册:
    2018-10-30
    帖子:
    382
    2023-08-24 #7
    共用吧~ 用了这样另一样就不能用, 很多板子都有这个问题
     
  8. xcgf

    xcgf Member

    注册:
    2019-11-30
    帖子:
    268
    2023-08-25 #8
    我没有安装任何m.2的硬盘
     
  9. bdrwu

    bdrwu Active Member

    注册:
    2018-10-30
    帖子:
    382
    2023-08-25 #9
    换个别的引导试试~ 我曾经遇过某个引导~ 裝完后 Video Station 里面任何档案都不会显示
    不是不显示缩图喔~ 而是不会显示任何档案, 永都是空的
    硬碟不换, 只更换引导.. 立即恢复正常
     
  10. xcgf

    xcgf Member

    注册:
    2019-11-30
    帖子:
    268
    2023-08-25 #10
    我就是不想用arpl 我没有办法'范-强'编译